Product Detail

Features/ Benefits

Simple 2 Button Programming -Change an array of settings without a PC! PC Programmable -Allows customization of all callbox attributes (PC and Programming Software Required) Reset Time Field Programmable -Change how long before the Callbox shuts down without software! Encode ANI (DTMF or 3 to 7 Tone Selcall) -Callbox can be programmed to transmit a unique numeric identifier to the appropriate decoding radio. Allows monitoring personnel to instantly identify callbox in use. Receiving radio requires proper decoding capability. See SLX display portable for Selcall decoding. Busy Channel TX Inhibit -Prevents Callbox from transmitting if someone else is using the radio channel Wide or Narrow Band Capable -Enables compatibility with most other radios systems Battery Powered or External AC Power Ready -Power the Callbox with 6 D Cell Batteries for maximum simplicity or 120 Volts AC (Use Ritron # RPS-EXPO Power Supply) Adjustable Speaker Volume -Control the volume of the Callbox speaker. Adjustable 1 to100% Adjustable Microphone Gain -Normal or high mic gain setting allows flexibility for different ambient noise environments Adjustable Transmit Power Output -Select 1or 2 Watt transmit setting (UHF Only). VHF 1 Watt only Automatic “Turn-Off” and “Always-On” Intercom Feature -Callbox can programmed to automatically “Turn-OFF” to conserve batteries or callbox can remain “ON” and in “Standby” Receive mode. (Use Ritron RPS-EXPO power supply.) Remote Control Relay -Built-in relay allows remote activation of Gate Controllers, Doors, Barrier Arms, and Stobe Lights connmected to the Callbox. Relay can also be used to turn an “attention getting” strobe light ON when callbox PTT button is pressed. Listen-In Feature -Callbox can be selectively paged to allow remote monitoring of audio in the area immediately surrounding the callbox.

Auxiliary Sensor Monitoring -Motion, Gate Entry, Tamper or Vehicle Detection Device. Callbox will send either a tone alert (6 Series) or custom voice alert (7 Series) when optional switch/sensor status changes. GateGuard Field Programmable -Enable the switch relay for operation of an external device without software! Automatic Turn-On Capability -A sensor connected to the auxiliary input can automatically turn the callbox ON to receive a call from radio-equipped personnel. Conserves batteries and quiets callbox until needed. Alert Tone – Low Battery Alert or External Power Fail -Distinct TONE sounds to alert radio-equipped personnel.

Prevents dead batteries or a power failure from blind siding you! 2-Tone Paging Decode (300-1500Hz) -Allows selective calling of indivudal callboxes 2-Tone Paging Decode All-Call -Allows selective calling of a group of callboxes simultaneously Companded Audio -Allows compatibility with these narrow band radio systems using companding technology Available In New FCC Channel Steps -2.5KHz VHF or 6.25KHz UHF Government Band Frequency -Now available in 406-421 MHz Recordable Voice “Greeting” -When the Callbox button is pressed, a “custom” greeting will play on the callbox speaker. Recordable Voice Messages -A separate and “custom” Voice Message Alert can be transmitted to alert radio-equipped personnel when Callbox button is pressed. No PTT button press required to send voice alert when these conditions are detected: AC power fail/low battery or when auxillary sensor status has changed. Automatic Voice Message Alert “Re-Send” -When Alert message from Callbox is not immediately answered, Alert message will automatically be “re-sent” up to 5 times. Number of “re-send” is selectable 0-5 times.

Features/ Benefits

Simple 2 Button Programming -Change an array of settings without a PC! PC Programmable -Allows customization of all callbox attributes (PC and Programming Software Required) Reset Time Field Programmable -Change how long before the Callbox shuts down without software! Encode ANI (DTMF or 3 to 7 Tone Selcall) -Callbox can be programmed to transmit a unique numeric identifier to the appropriate decoding radio. Allows monitoring personnel to instantly identify callbox in use. Receiving radio requires proper decoding capability. See SLX display portable for Selcall decoding. Busy Channel TX Inhibit -Prevents Callbox from transmitting if someone else is using the radio channel Wide or Narrow Band Capable -Enables compatibility with most other radios systems Battery Powered or External AC Power Ready -Power the Callbox with 6 D Cell Batteries for maximum simplicity or 120 Volts AC (Use Ritron # RPS-EXPO Power Supply) Adjustable Speaker Volume -Control the volume of the Callbox speaker. Adjustable 1 to100% Adjustable Microphone Gain -Normal or high mic gain setting allows flexibility for different ambient noise environments Adjustable Transmit Power Output -Select 1or 2 Watt transmit setting (UHF Only). VHF 1 Watt only Automatic “Turn-Off” and “Always-On” Intercom Feature -Callbox can programmed to automatically “Turn-OFF” to conserve batteries or callbox can remain “ON” and in “Standby” Receive mode. (Use Ritron RPS-EXPO power supply.) Remote Control Relay -Built-in relay allows remote activation of Gate Controllers, Doors, Barrier Arms, and Stobe Lights connmected to the Callbox. Relay can also be used to turn an “attention getting” strobe light ON when callbox PTT button is pressed. Listen-In Feature -Callbox can be selectively paged to allow remote monitoring of audio in the area immediately surrounding the callbox.

Auxiliary Sensor Monitoring -Motion, Gate Entry, Tamper or Vehicle Detection Device. Callbox will send either a tone alert (6 Series) or custom voice alert (7 Series) when optional switch/sensor status changes. GateGuard Field Programmable -Enable the switch relay for operation of an external device without software! Automatic Turn-On Capability -A sensor connected to the auxiliary input can automatically turn the callbox ON to receive a call from radio-equipped personnel. Conserves batteries and quiets callbox until needed. Alert Tone – Low Battery Alert or External Power Fail -Distinct TONE sounds to alert radio-equipped personnel.

Prevents dead batteries or a power failure from blind siding you! 2-Tone Paging Decode (300-1500Hz) -Allows selective calling of indivudal callboxes 2-Tone Paging Decode All-Call -Allows selective calling of a group of callboxes simultaneously Companded Audio -Allows compatibility with these narrow band radio systems using companding technology Available In New FCC Channel Steps -2.5KHz VHF or 6.25KHz UHF Government Band Frequency -Now available in 406-421 MHz Recordable Voice “Greeting” -When the Callbox button is pressed, a “custom” greeting will play on the callbox speaker. Recordable Voice Messages -A separate and “custom” Voice Message Alert can be transmitted to alert radio-equipped personnel when Callbox button is pressed. No PTT button press required to send voice alert when these conditions are detected: AC power fail/low battery or when auxillary sensor status has changed. Automatic Voice Message Alert “Re-Send” -When Alert message from Callbox is not immediately answered, Alert message will automatically be “re-sent” up to 5 times. Number of “re-send” is selectable 0-5 times.

Features/ Benefits

Simple 2 Button Programming -Change an array of settings without a PC! PC Programmable -Allows customization of all callbox attributes (PC and Programming Software Required) Reset Time Field Programmable -Change how long before the Callbox shuts down without software! Encode ANI (DTMF or 3 to 7 Tone Selcall) -Callbox can be programmed to transmit a unique numeric identifier to the appropriate decoding radio. Allows monitoring personnel to instantly identify callbox in use. Receiving radio requires proper decoding capability. See SLX display portable for Selcall decoding. Busy Channel TX Inhibit -Prevents Callbox from transmitting if someone else is using the radio channel Wide or Narrow Band Capable -Enables compatibility with most other radios systems Battery Powered or External AC Power Ready -Power the Callbox with 6 D Cell Batteries for maximum simplicity or 120 Volts AC (Use Ritron # RPS-EXPO Power Supply) Adjustable Speaker Volume -Control the volume of the Callbox speaker. Adjustable 1 to100% Adjustable Microphone Gain -Normal or high mic gain setting allows flexibility for different ambient noise environments Adjustable Transmit Power Output -Select 1or 2 Watt transmit setting (UHF Only). VHF 1 Watt only Automatic “Turn-Off” and “Always-On” Intercom Feature -Callbox can programmed to automatically “Turn-OFF” to conserve batteries or callbox can remain “ON” and in “Standby” Receive mode. (Use Ritron RPS-EXPO power supply.) Remote Control Relay -Built-in relay allows remote activation of Gate Controllers, Doors, Barrier Arms, and Stobe Lights connmected to the Callbox. Relay can also be used to turn an “attention getting” strobe light ON when callbox PTT button is pressed. Listen-In Feature -Callbox can be selectively paged to allow remote monitoring of audio in the area immediately surrounding the callbox.

Auxiliary Sensor Monitoring -Motion, Gate Entry, Tamper or Vehicle Detection Device. Callbox will send either a tone alert (6 Series) or custom voice alert (7 Series) when optional switch/sensor status changes. GateGuard Field Programmable -Enable the switch relay for operation of an external device without software! Automatic Turn-On Capability -A sensor connected to the auxiliary input can automatically turn the callbox ON to receive a call from radio-equipped personnel. Conserves batteries and quiets callbox until needed. Alert Tone – Low Battery Alert or External Power Fail -Distinct TONE sounds to alert radio-equipped personnel.

Prevents dead batteries or a power failure from blind siding you! 2-Tone Paging Decode (300-1500Hz) -Allows selective calling of indivudal callboxes 2-Tone Paging Decode All-Call -Allows selective calling of a group of callboxes simultaneously Companded Audio -Allows compatibility with these narrow band radio systems using companding technology Available In New FCC Channel Steps -2.5KHz VHF or 6.25KHz UHF Government Band Frequency -Now available in 406-421 MHz Recordable Voice “Greeting” -When the Callbox button is pressed, a “custom” greeting will play on the callbox speaker. Recordable Voice Messages -A separate and “custom” Voice Message Alert can be transmitted to alert radio-equipped personnel when Callbox button is pressed. No PTT button press required to send voice alert when these conditions are detected: AC power fail/low battery or when auxillary sensor status has changed. Automatic Voice Message Alert “Re-Send” -When Alert message from Callbox is not immediately answered, Alert message will automatically be “re-sent” up to 5 times. Number of “re-send” is selectable 0-5 times.